カゴの中を見る

商品数:0点

合計:0円

カゴの中を見る

商品を探す

商品カテゴリから選ぶ

商品名を入力

検索結果で出ない商品は

お問い合わせ下さいませ

商品カテゴリ

分野別

商品コード: ASTM-A370-2020

ASTM A370: 2020

販売価格(税込10%): 17,547 円
種類別の販売価格、在庫状況を見る
在庫区分
申し訳ございませんが、只今売切れ中です。

商品おすすめポイント

書名

ASTM A370: 2020: Standard Test Methods and Definitions for Mechanical Testing of Steel Products
出版社/発行元 ASTM International (ASTM)
発行年/月 2020年8月   
装丁 ペーパー
ページ数/巻数 50ページ
発送予定 海外倉庫よりお取り寄せ 1-2週間以内に発送します

 

◆本商品は新ウェブショップにて販売しております。ご注文ご希望のお客様は新ウェブショップにご来店ください◆

 

 

 

※PDF版、PDF版+冊子版をご希望のお客様は別途お問合せ下さいませ
※当ウェブ・ショップに掲載のない規格につきましては、別途お問合せ下さいませ。
※掲載の規格は、当ウェブ・ショップに掲載時点で確認できた最新版でございます。
最新の発行状況につきましては受注時に改めて確認をさせて頂きますので予めご了承下さい。

 

Description

 

ASTM A370, 2020 Edition, August 1, 2020 - Standard Test Methods and Definitions for Mechanical Testing of Steel Products

These test methods2 cover procedures and definitions for the mechanical testing of steels, stainless steels, and related alloys. The various mechanical tests herein described are used to determine properties required in the product specifications. Variations in testing methods are to be avoided, and standard methods of testing are to be followed to obtain reproducible and comparable results. In those cases in which the testing requirements for certain products are unique or at variance with these general procedures, the product specification testing requirements shall control.

The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

When these test methods are referenced in a metric product specification, the yield and tensile values may be determined in inch-pound (ksi) units then converted into SI (MPa) units. The elongation determined in inch-pound gauge lengths of 2 or 8 in. may be reported in SI unit gauge lengths of 50 or 200 mm, respectively, as applicable. Conversely, when these test methods are referenced in an inch-pound product specification, the yield and tensile values may be determined in SI units then converted into inch-pound units. The elongation determined in SI unit gauge lengths of 50 or 200 mm may be reported in inch-pound gauge lengths of 2 or 8 in., respectively, as applicable.

The specimen used to determine the original units must conform to the applicable tolerances of the original unit system given in the dimension table not that of the converted tolerance dimensions.

NOTE 1-This is due to the specimen SI dimensions and tolerances being hard conversions when this is not a dual standard. The user is directed to Test Methods A1058 if the tests are required in SI units.

Attention is directed to ISO/IEC 17025 when there may be a need for information on criteria for evaluation of testing laboratories.

This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

種類別の販売価格、在庫状況を見る
在庫区分

この商品に対するお客様の声

 

mitsumori

見積書をお送り致します

 

 

  新刊案内など配信中!!

 

このページのTOPへ